IR Design Requirements
This page discusses the requirements imposed by the EIC physics on the IR design.
The following requirements will be discussed in more detail below
- the detection of neutrons of nuclear break up in the outgoing hadron beam direction
- the detection of the scattered protons from exclusive and diffractive reaction in the outgoing proton beam direction
- the detection of the spectator protons from 3He in polarized e+3He collisions
- the beam element free region around the IR and the requirements on the magnetic field of the detector
- space for low Q2 scattered lepton detection
- space for the luminosity monitor in the outgoing lepton beam direction
- space for lepton polarimetry
For exclusive and diffractive reactions in e-A scattering it is essential to detect the neutron of the nuclear break up in the direction of the outgoing beam. The figure below shows the scattering angle distribution for breakup neutrons from a gold nucleus for different excitation energies of the nucleus.
These distributions lead to the requirement of a angular acceptance of +/- 3mrad to allow to detect these neutrons in the ZDC
To reconstruct the Mandelstam variable t, which represents the momentum transfer to the proton in exclusive reactions, it is critical to detect the forward going scattered proton. t is essential in exclusive reactions as it can be fourier transformed to the impact parameter b, which gives the transverse spatial distribution of partons in the proton. The figure below shows the scattering angle θ for three different center-of-mass energies as a function of the scattered proton momentum.
This poses the following requirement that for different hadron beam energies 100 GeV and 250 GeV protons with a momentum 20% lower then the proton beam energy and a scattering angles up to 12 mrad need to be transported through the different magnets.
There is only a very weak correlation between the momentum and the scattering angle. These protons cannot be detected in the main detector. The standard detectors used to detect the scattered proton are roman pots placed at different distances from the IR. Using this detector technology poses an other requirement on the machine performance. To reach as small scattering angles as possible a small emittance of the beam is crucial as there is also an additional requirement of 10 σ clearance from the core of the beam.
To have good acceptance at low scattering angle the beam needs to be cooled in transverse direction to achieve a beam angular divergence of ~100μrad
-Crucial for identifying processes with a neutron “target” (e+n) in e+3He.
-Spectator neutron (<~3 mrad) can be measured by ZDC.
-Tagging spectator protons from 3He.
- Relying on separation from magnetic rigidity (Br) changes 3He: p = 3/2:1
- No need to reconstruct momentum but need clean identification: position+directional measurement
- Common detectors (Roman Pots) can be utilized for tagging forward proton from DVCS and the spectator protons from 3He
Scattering angle vs. momentum of spectator protons in e+3He at 10(e)x100(N) GeV [left]. The projections in angle (mrad) and momentum (p) are shown in the center and right panels. The acceptance of the protons at the detector depends on the IR optics of the beam. The calculation was done using DPMJETIII with Fluka implementation. The requirements of the detectors for the spectator tagging with an IR design can be found here.
Detector Space and Magnetic Field
the detector needs a +/- 4.5m beam element free region.
Any magnetic field which is introduced in addition to the solenoidal field of the detector, needs to obey the following requirements.
- the region of the RICH in the forward and backward direction should be free of any magnetic field
- the magnetic field homogeneity needs to obey the requirements posed by the TPC
- the bore of the solenoid must have at least a radius of 1m
- the forward tracking resolution must be retained
for many physics topics it is important to tag the scattered lepton at very small scattering angles and such as very low Q2.
The main detector covers -4 to 4 in rapidity for the scattered lepton. So scattered leptons with a scattering angle > 178 degree will not be detected in the main detector. The plots below correlate the momentum of the scattered lepton with its scattering angle and its Q2. To see some of these low Q2 leptons it is important to separate the scattered lepton from the outgoing lepton beam. To have a reasonable low Q2 acceptance the requirement for the IR is to transport
leptons with 10% momentum of the full beam energy (Ee' >= 0.9 E) and with a scattering angle from 179.5 to 178 degree (180 degree being the outgoing beam) through the magnets.
The resulting Q2 distribution after applying all the requirements listed above is shown in the 4th row below.
to achieve the precision needed for the luminosity measurement to match the statistical uncertainties anticipated for eRHIC, it is important to follow and improve the concept of luminosity measurements at HERA as described in here. The technique involves a electromagnetic calorimeter for photon detector and a pair spectrometer. The picture below shows a schematic view of the ZEUS layout a similar layout needs to be realized for eRHIC.
requirements need still to be worked out